Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - tolgahan

Pages: [1]
1
I need help / Drserver connection problem ( yes again )
« on: 2019-11-27, 18:56:03 »
I've been trying for eight hours, but I can't figure it out.

not a hardisk problem...

Cannot save temporary DR scene to: [file name]
Modified on: Thu, 22 Oct, 2015 at 5:27 PM

Cannot save temporary DR scene to: [file name]

This message means Corona was unable to save temporary distributed rendering scene file on the master machine. Default scene saving location is:

C:\Users\[username]\AppData\Local\Autodesk\3dsMax\2016 - 64bit\ENU\en-US\plugcfg\corona



Possible causes:

An internal error occurred when attempting to save temporary DR scene file.



Solutions:

Make sure you have enough free hard drive space
In case you have enough hard drive space, please report this problem at: https://corona-renderer.com/forum/ or submit a new support ticket

Same problem

the same thing happened on my other machine..Two of the 6 machines do not start drserver.I had no problems in the previous version.I moved to 3dsmax 2020, could it be related?








2
I started to open layers in stages

I seperated multiscatter layer from corona scatter layer

I seperated the trees and objects

Up to a point I had no problems in render

Finally when I was about to open all the necessary layers the corona notification became like this in the screenshots

Did I overload it or is it normal

I had no problems until 50-60 millions poly

additionally on the last scene I increased the resolution from 5k to 5k

I'd be glad If you could read the data hear let me know If there is any problem or not















7516 hours :)))






3
I need help / UHD Cache question
« on: 2016-08-09, 10:37:35 »

I have some questions about uhd cache.

Imagine turning 360 degrees around a square building. At which frame shall i save uhd cache? In the front of the building, at the back or on the side of the building?

Is it logical to make precision 20 as we will wait only for one uhd cache? What can we do for less flickers?

For instance at which number would we have a better result for gi vs aa balance animation?

I want to make waves with animated noise on the water. Would it work to pre-save uhd cache or should i use still frame computed?



No denoiser
65 pass per frame
1080p


Full hd 1080 p
420 frame
Every frame 60 pass and full denoising




https://corona-renderer.com/forum/index.php/topic,12539.0/all.html

4
I need help / Longest Hours..
« on: 2016-07-27, 21:01:55 »
There 's something wrong here...



I am still waiting..

5
I need help / DR & BACKBURNER PROBLEM
« on: 2016-07-14, 19:08:38 »
1.    There’s a main machine at the farm. I connect with Vnc. I stop it on an open corona frame buffer screen because there is no need to continue rendering on there. I want it to start the other render in the list.

2.    14 drserver renders. After render finishes there’s no error. When the next render starts sometimes 4 or 5 machine does not close 3dsmax and waits. When I close and open cms screens as shown in the video, it starts the new render. But at the background there remains two max open. I mean max does not resart for the new work.

3.    In every option drservers should definitely reset.

A-   When clicked on Stop

B-   When cancelled on backburner.

C-   When render passes completed.

 
4.    I get no error warnings. Drserver says it is waiting for the new render. But the new render does not reach to the machine where the drserver is. 4 render finishes and sometimes I have no error and sometimes when the second render finishes I get an error.

5.    You can see them on the screenshots I sent you. This happens all the time. Havent you ever seen such problem? I have this problem when/if at the corona frame buffer screen dr part on the main machine cannot connect. The number shown at the top keeps increasing. Therefore I cannot check if 14 machines are connected or not.

6.    All the machines are slave. Corona drserver works on all. I send through backburner.

7.    I use 1.4 version both corona and drservers.

I think it is because of the scene. Probably to do with drserver.

Check my attachment pls.Render is finished but 3dsmax is still running.When ı closed the cmd screen.New render is proccesing.Its like a russian rouloutte.

ANY BACKBURNER USER ?


6
Work in Progress/Tests / Avisgrafik_Corona_tests(WIP)
« on: 2016-07-11, 13:24:52 »
Corona render...

Updated 11.10.2016































It was the first time I enjoyed working. Rather than coping with the settings I played with lightings, shadowing, camera angles etc. I work for different tastes now. Even getting awkward results has started to entertain me. After finishing my commercial job the first thing I’ll do is going to be making 3ds of my sci-fi sketches.















Playing enviroment fog...
















..............................................................Trails , trails... ( Plants and greens )

Trying to find the best green

Dof






























7
I need help / BACKBURNER PROBLEM
« on: 2015-02-27, 16:57:42 »

When I take dr server on my main machine, the scene is rendered. But when I want to render the scene by using backburner, Dr servers continuously turn on and off. I cant see any errors with MAXLOG and DRLOG. Backburner causes problems. How can we sort it out?

8
I need help / Help my animation setup...
« on: 2015-02-17, 10:50:03 »
I’m using 1.0 version.
 
There are some stuff I don’t understand about Dr. When I turn on the slave machine, it’s going like pass1 pass2 pass3 pass4 and then going back to pass1 again.
 
I choose primary solver path tracing secondary solver uhd cache (animation flickerfree is selected) and then I choose the first frame and calculate from strach.
 
Every 30 frames when I think it’s necessary, I do ‘try to load and append’ and when I want to start the main animation I load from the file.
 
1.    How do I know what the uhd cache file is saving?

2.    Slave machines turn off and on max every time. Is there a way to stop this? Max sends the file from the main machine to the slave machine at each frame. How can I sort this out?

 
Is there anything that I’m doing wrong?
 

9
Work in Progress/Tests / Tolgahan_WIP
« on: 2015-02-16, 16:55:16 »
I started to some vrayproxy convert tests and dr


10
Gallery / Tolgahan-Corona(avisgrafik)
« on: 2015-02-14, 11:47:30 »
Hello...

Our latest commercial works. MODDA BULVAR

Visualization studio : Avisgrafik

Design & branding : Nevcreative

11
I need help / Distrubated rendering problem slippy renders
« on: 2015-02-08, 16:47:15 »
Hi...

I am getting an error saying: '' replying to discovery ping from '' when I send backburner from the computer I work to another computer.
 
Other 10 Slave computer gives the same error. When the computer that I have backburner on is rendering, the other computer that has Slave cannot join it.
 
Apart from this, when I render on my computer, all other slaves are rendering . I think there’s a problem with backburner that I cannot sort out.
 

Thanks...





www.avisgrafik.com
https://www.facebook.com/Avisgrafik

Pages: [1]